Tile Installation Tips by Woodmont At Wawayanda Orange County NY Homes for Sale,

Tile installation can be a hectic process if you have no idea about the subject. On the other hand, Tile Installation can be a piece of cake when you are focused on the things you’re doing and have everything planned out.

Like most other day to day jobs, tile installation isn’t a tough nut to crack. All you need is a well planned scheme, organization, and a few basic things to be taken care of here and there.

First step in any tile installation process involves removing the old tiles and preparing the surface for the new tiles (of course if you are buying one of our Homes for Sale in Orange County New York, you will already have new flooring). The sub floor must be sound enough to support tile. Tile can be heavy and must be installed on a flat, rigid surface. Sub floors under tile should be no less than 1" thick. A flexing floor will cause cracks to show up in the grout later and may cause tiles to break.

Uneven or damaged surfaces are best covered first with an underlayment as the tile base. Cement-fiber board is often recommended by tile manufacturers for use on floors in a moist environment.

If the floor is concrete, you should repair any holes or cracks first. You can sometimes lower high spots using a coarse-grit abrasive on a belt or disc sander. Any minor bumps can be removed with a cold chisel driven by a baby sledge hammer (be sure to wear safety glasses.)

Second obvious question that may arise while installing tiles is “what kind of pattern do I use?”

The pattern options available when laying tile are virtually endless. However, there are two basic patterns:

A "jack-on-jack" pattern is the most common. The pattern consists of tile laid like squares on a checkerboard.

A "running bond" pattern has offset grout lines for each row.

Either is fairly easy to set, although the running bond pattern is the more difficult of the two.

The Third Step involves planning the layout. Tiles should be centered in the room for the best visual appearance. Keep this in mind when you lay out the floor tile.

Measure and find the center of two opposite walls. Use these points to snap a chalk line across the length of the room in the center of the floor, dividing the room in half. Then snap another chalk line perpendicular to the first so the two lines cross in the center of the room. Check where the lines cross with a carpenter's square to make absolutely sure the center point is square.

Dry fit a row of tiles down both lines to the width and length of the room. Leave equal spacing for the grout joints. Most floor tiles do not come with spacers like wall tiles do, so you will need to approximate the appropriate spacing. By laying out the tiles in this way, you can get an idea of any adjustments that need to be made to your original reference lines. The goal is to work with as many full tiles as possible. Also, you should end up with at least half a tile width in the areas where the tiles meet the walls. A slight adjustment at the center point may save you lots of time and money. Adjust the reference lines as necessary to achieve a layout you are satisfied with.

The Fourth step is crucial, which involves installing the tile on the surface

• Begin laying the tile from the center of the surface where your two final reference lines cross. Start by laying a tile at the intersection of the lines, and then use the lines as a guide as you work your way outward toward the walls in each quadrant.

• Spread the adhesive with the trowel's notched edge, combing it out in beaded ridges. Spaces between ridges of adhesive should be almost bare.

• If you wish, you may insert plastic spacers between the tiles to help maintain straight grout lines if the tiles do not have spacer lugs. Remove these after placing the tile but before they become firmly set in the adhesive.

• If adhesive oozes up between the tiles, clean out the excess before it dries. Immediately wipe any adhesive from the face of the tiles with a solvent-soaked sponge or rag. (Consult the manufacturer's instructions to determine the appropriate solvent). Adhesives begin to set firmly in 20 to 30 minutes.

• After you have installed several rows of tile, set them into the adhesive with the tile leveler and a mallet.

• After laying all the whole tiles that will fit, begin cutting and adhering tiles to fill around the perimeter of the room.

The Final step involves grouting the joints where grout is mixed and used up for tiling process to make the surface firm.

In this way, when carefully planned and carried out, tile installation process can be a piece of cake, adding to the beauty of your house and at the same time, leading to a sense of personal achievement and satisfaction.

This article on Tile Installation was provided by Woodmont At Wawayanda, providing New Home Construction Orange County NY.

Filed under: House and Home

Like this post? Subscribe to my RSS feed and get loads more!